Altera CPRI IP Core Manuel d'utilisateur Page 122
- Page / 220
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7–6 Chapter 7: Software Interface
CPRI Protocol Interface Registers
CPRI MegaCore Function December 2013 Altera Corporation
User Guide
Table 7–8. CPRI_RX_CTRL—CPRI Received Control Word—Offset: 0x10
Field Bits Access Function Default
rx_control_data
[31:0] RW
Most recent received CPRI control word 32-bit section from
CPRI hyperframe position Z.x, where x is the index in the
cpri_ctrl_index
field of the
CPRI_CTRL_INDEX
register. The
cpri_ctrl_position
field of the
CPRI_CTRL_INDEX
register
indicates whether this is the first, second, third, or fourth such
32-bit section.
32'h0
Table 7–9. CPRI_TX_CTRL—CPRI Transmit Control Word—Offset: 0x14
Field Bits Access Function Default
tx_control_data
[31:0] RW
CPRI control word 32-bit section to be transmitted in CPRI
hyperframe position Z.x, where x is the index in the
cpri_ctrl_index
field of the
CPRI_CTRL_INDEX
register.
The
cpri_ctrl_position
field of the
CPRI_CTRL_INDEX
register indicates whether this is the first, second, third, or
fourth such 32-bit section.
32'h0
Table 7–10. CPRI_LCV—CPRI Line Code Violation Counter—Offset: 0x18
Field Bits Access Function Default
RSRV
[31:8] UR0 Reserved.
24'h0
cpri_lcv
[7:0] RO
Number of line code violations (LCVs) detected in the 8B/10B
decoding block in the transceiver. Enables CPRI link
debugging. This register saturates at the value 255; after it
reaches 255, it maintains this value until reset.
This counter is not used to determine whether the N_LCV
threshold (Table 7–23 on page 7–12) is reached, because it
includes LCVs that occur during initialization—before T_LCV
(Table 7–24 on page 7–12) is reached—and because it
saturates.
8’h0
Table 7–11. CPRI_BFN—CPRI Recovered Radio Frame Counter—Offset: 0x1C
Field Bits Access Function Default
RSRV
[31:12] UR0 Reserved.
20'h0
bfn
[11:0] RO
Current BFN (node B radio frame number) number. Value
obtained from BFN alignment state machine.
12’h0
Table 7–12. CPRI_HW_RESET—Hardware Reset From Control Word—Offset: 0x20 (Part 1 of 2)
Field Bits Access Function Default
RSRV
[31:8] UR0 Reserved.
24'h0
reset_gen_done_hold
[7] RC Hold
reset_done
.
1’h0
reset_gen_done
[6] RO
Indicates that a reset request or acknowledgement has been
successfully sent on the CPRI link by the CPRI transmitter.
1'h0
reset_detect_hold
[5] RC
(1)
Hold
reset_detect
.
1'h0
- User Guide 1
- CPRI MegaCore Function 1
- Contents 3
- Chapter 5. Testing Features 4
- ContentsContents v 5
- General Description 8
- CPRI IP Core Features 10
- Device Family Support 11
- MegaCore Verification 12
- Release Information 14
- Installation and Licensing 15
- OpenCore Plus Evaluation 16
- 2. Getting Started 17
- Specifying Parameters 18
- Simulation Files 19
- Simulating the Design 20
- Supporting the Transceivers 21
- Specifying Constraints 21
- 3. Parameter Settings 25
- Operation Mode Parameter 26
- Line Rate Parameter 26
- Enable Autorate Negotiation 27
- Rx Elastic Buffer Depth 27
- Include MAC Block 28
- Include HDLC Block 29
- Mapping Mode 29
- Application Layer Parameters 30
- Words” on page 4–42 32
- 4. Functional Description 33
- Architecture Overview 34
- CPRI IP Core Clocks 35
- Clocking Structure 36
- Notes to Table 4–2: 42
- Reset Requirements 43
- MegaCore 44
- Function 44
- MAP Interface Mapping Modes 45
- Basic AxC Mapping Mode 46
- MAP Interface 47
- Note to Table 4–5: 49
- Note to Table 4–6: 49
- Advanced AxC Mapping Modes 50
- MAP Receiver Interface 50
- Notes to Table 4–7: 51
- MAP Receiver in FIFO Mode 52
- MAP Transmitter Interface 56
- Notes to Table 4–10: 57
- MAP Transmitter in FIFO Mode 58
- Auxiliary Interface 62
- AUX Receiver Module 63
- Avalon-ST 32-bit interface 64
- AUX Transmitter Module 66
- Note to Figure 4–19: 67
- MII Transmitter 70
- MII Receiver 71
- CPU Interface 73
- Control Word Order 78
- Transmitting Ethernet Traffic 80
- Receiving Ethernet Traffic 81
- Accessing the HDLC Channel 82
- Note to Table 4–15: 83
- Features 84
- Physical Layer Architecture 84
- Receiver 85
- High-Speed Transceiver 86
- Rx Elastic Buffer 86
- Descrambling 87
- Frame Synchronization 87
- Alarm Indications 88
- Reset Control Word 89
- Transmitter 90
- Scrambling 91
- Tx Elastic Buffer 91
- External Loopback 93
- CPRI IP Core 93
- Internal Reverse Loopback 94
- Physical Layer Loopback Mode 94
- (1) (2) (3) 96
- MAP Receiver Signals 99
- 6–2 Chapter 6: Signals 100
- MAP Interface Signals 100
- MAP Transmitter Signals 101
- 6–4 Chapter 6: Signals 102
- Auxiliary Interface Signals 103
- AUX Receiver Signals 104
- AUX Transmitter Signals 105
- 6–8 Chapter 6: Signals 106
- Extended Rx Status Signals 107
- CPRI MII Receiver Signals 108
- CPRI MII Transmitter Signals 108
- CPU Interface Signals 109
- CPRI Data Signals 110
- Layer 1 Error Signal 111
- Autorate Negotiation Signals 111
- 6–14 Chapter 6: Signals 112
- Physical Layer Signals 112
- Transceiver Signals 113
- 6–16 Chapter 6: Signals 114
- Note to Table 6–14: 115
- 6–18 Chapter 6: Signals 116
- 7. Software Interface 117
- Note to Table 7–5: 119
- CPRI_HW_RESET 123
- register, refer to “Reset 123
- Requirements” on page 4–11 123
- Note to Table 7–13: 124
- Note to Table 7–16: 125
- Note to Table 7–17: 126
- Note to Table 7–20: 126
- Notes to Table 7–21: 127
- Notes to Table 7–28: 130
- Notes to Table 7–29: 130
- Note to Table 7–32: 133
- Note to Table 7–33: 133
- Note to Table 7–34: 133
- Note to Table 7–35: 134
- Note to Table 7–36: 134
- Notes to Table 7–37: 135
- Notes to Table 7–38: 135
- Notes to Table 7–39: 136
- Notes to Table 7–40: 136
- Note to Table 7–45: 137
- Ethernet Registers 138
- HDLC Registers 143
- Note to Figure 8–1: 150
- Test Sequence 151
- Running the Testbench 153
- A. Initialization Sequence 155
- Negotiation 157
- Notes for Figure B–1: 158
- Running Autorate Negotiation 159
- Notes to Table C–3: 167
- D. Advanced AxC Mapping Modes 173
- Fifteen-Bit Width Mode 175
- Sixteen-Bit Width Mode 176
- Note to Figure D–2: 177
- Delay Requirements 179
- RE SlaveREC Master 180
- Rx Path Delay 181
- Most CPRI IP Core Variations 181
- Single-Hop Delay Measurement 182
- Notes to Table E–1: 183
- Notes to Table E–2: 184
- Notes to Table E–3: 186
- Arria V GT 9.8 Gbps 188
- Notes to Table E–4: 189
- Tx Path Delay 190
- Note to Table E–6: 192
- T_txv_TX 194
- in Figure E–1 on page E–2 194
- Round-Trip Delay 196
- Round-Trip Cable Delay 196
- Families 202
- Round-Trip Delay Calculation 205
- Multi-Hop Delay Measurement 206
- Additional Information 213
- Document Revision History 214
- How to Contact Altera 218
- Typographic Conventions 218
Produits connexes et manuels pour Instruments de mesure Altera CPRI IP Core
(38 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels