Altera RapidIO II MegaCore Function Manuel d'utilisateur Page 105
- Page / 218
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 4: Functional Description 4–63
Logical Layer Interfaces
August 2014 Altera Corporation RapidIO II MegaCore Function
User Guide
Table 4–38 lists the header fields of the received response packet in this example.
User Receiving Read Request and Sending Read Response
Table 4–39 lists the Avalon-ST pass-through interface usage example this section
describes. Refer to “Transaction ID Ranges” on page 4–48 and “Receiver” on
page 4–71 for a description of the RapidIO II IP core variations in which this example
transaction is processed through the Avalon-ST pass-through interface rather than
being processed through one of the I/O Logical layer modules.
Table 4–38. NREAD Response Receive Example: RapidIO Header Fields in gen_rx_hd_data Bus
Field
gen_rx_hd_data
Bits
Value Comment
pd_size[8:0]
[114:106] 9’h020 Payload data size is 0x20 (decimal 32).
VC
[105] 0 The RapidIO II IP core supports only VC0.
CRF
[104] 0
prio[1:0]
[103:102] 2’b10
Priority of the response packet. Value must be higher
than the priority value of the request packet. In this
example, the response packet has a priority value of
2’b10 and the original request has a priority value of
2’b01.
tt[1:0]
[101:100] 2’b01 Indicates 16-bit device IDs.
ftype[3:0]
[99:96] 4’b1101
The value of 4’hD (decimal 13) indicates a Response
Class packet.
destinationID[15:0]
[95:80] 16’hAAAA
The sourceID and destinationID of the NREAD request
are swapped in the response transaction.
sourceID[15:0]
[79:64] 16’hDDDD
ttype[3:0]
[63:60] 4’b1000
The value of 8 indicates a Response transaction with
data payload.
status[3:0]
[59:56] 4’b0000
The value of 0 indicates Done. The current packet
successfully completes the requested transaction.
transactionID[7:0]
[55:48] 8'hBB
Value in the response packet matches the
transactionID
of the corresponding request packet.
Reserved[47:0]
[47:0] 48’h0
Table 4–39. Avalon-ST Pass-Through Interface Usage Example: Receiving NREAD Request and Sending Response
User Operation
Operation
Type
RapidIO Transaction Priority
Device ID
Width
Payload Size
(Bytes)
Receive read request Rx NREAD 1 16 32
Send read response Tx Response with payload 2 16 32
- User Guide 1
- RapidIO II MegaCore Function 1
- Contents 3
- Contents v 5
- Chapter 5. Signals 6
- Chapter 6. Software Interface 6
- Chapter 7. Testbench 6
- 1. About The RapidIO II 9
- MegaCore Function 9
- Releases 10
- RapidIO II IP Core Features 10
- Features 11
- Device Family Support 12
- IP Core Verification 13
- Hardware Testing 14
- Interoperability Testing 14
- Note to Table 1–3: 16
- Notes to Table 1–4: 16
- Installation and Licensing 17
- 2. Getting Started 19
- Simulating IP Cores 22
- Transceiver Settings 26
- External Transceiver PLL 26
- 3. Parameter Settings 31
- Note to Table 3–1: 32
- Enable 16-Bit Device ID Width 33
- Logical Layer Settings 34
- Capability Registers Settings 35
- Device ID 36
- Vendor ID 36
- Revision ID 36
- Assembly ID 36
- Assembly Information CAR 37
- Enable Flow Control Support 38
- Enable Switch Support 38
- Number of Ports 38
- Port Number 39
- Maximum PDU 39
- Destination Operations CAR 40
- Port General Control CSR 40
- Port 0 Control CSR 41
- Lane n Status 0 CSR 41
- Extended Features Pointer CSR 41
- 4. Functional Description 43
- Note to Table 4–2: 44
- Clocking and Reset Structure 45
- Notes to Table 4–3: 46
- RapidIO II 47
- Transactions 55
- Notes to Table 4–6: 57
- Notes to Table 4–7: 59
- Note to Table 4–8: 59
- Note to Figure 4–9: 66
- Note to Table 4–10: 70
- Notes to Table 4–11: 71
- Table 6–60 on page 6–40 72
- Note to Table 4–12: 73
- Maintenance Module 74
- Maintenance Interface Signals 75
- Doorbell Module Block Diagram 86
- Preserving Transaction Order 87
- Doorbell Module Signals 88
- Generating a Doorbell Message 88
- Receiving a Doorbell Message 89
- Transaction ID Ranges 90
- Notes to Table 4–24: 92
- Note to Table 4–26: 94
- Note to Table 4–27: 95
- field 97
- User Receiving Write Request 100
- Logical Layer Interfaces 101
- Transport Layer 112
- Receiver 113
- Transmitter 114
- Physical Layer 115
- Physical Layer Interfaces 116
- Low-level Interface Receiver 116
- CRC Checking and Removal 117
- Protocol Violations 119
- Fatal Errors 119
- Maintenance Avalon-MM Slave 120
- Maintenance Avalon-MM Master 121
- Port-Write Reception Module 122
- Input/Output Avalon-MM Slave 122
- Input/Output Avalon-MM Master 123
- 5. Signals 125
- Physical Layer Signals 126
- Low Latency Signals 127
- Multicast Event Signals 128
- Chapter 5: Signals 5–5 129
- Note to Table 5–7: 130
- Chapter 5: Signals 5–7 131
- 5–8 Chapter 5: Signals 132
- Register-Related Signals 133
- Avalon-MM Interface Signals 133
- Note to Table 5–12: 134
- Chapter 5: Signals 5–11 135
- Note to Table 5–15: 136
- Error Reporting Signals 137
- 5–14 Chapter 5: Signals 138
- 6. Software Interface 139
- Memory Map 140
- Physical Layer Registers 144
- Note to Table 6–9: 147
- Note to Table 6–14: 154
- Note to Table 6–15: 158
- Note to Table 6–17: 160
- Note to Table 6–22: 164
- Note to Table 6–23: 164
- Note to Table 6–24: 165
- Note to Table 6–25: 165
- Note to Table 6–26: 166
- Note to Table 6–27: 167
- Notes to Table 6–28: 168
- Notes to Table 6–29: 169
- Note to Table 6–30: 169
- Note to Table 6–31: 169
- Notes to Table 6–32: 170
- Note to Table 6–34: 171
- Note to Table 6–35: 171
- Note to Table 6–36: 172
- Note to Table 6–37: 172
- Transmit Port-Write Registers 174
- Receive Port-Write Registers 175
- Note to Table 6–59: 178
- Error Management Registers 180
- Note to Table 6–66: 181
- Notes to Table 6–67: 183
- Notes to Table 6–70: 185
- Notes to Table 6–71: 185
- Doorbell Message Registers 191
- Note to Table 6–89: 193
- 7. Testbench 195
- 7–2 Chapter 7: Testbench 196
- Testbench Overview 196
- Testbench Sequence 197
- 7–4 Chapter 7: Testbench 198
- Chapter 7: Testbench 7–5 199
- SWRITE Transactions 200
- NREAD Transactions 200
- NWRITE_R Transactions 201
- NWRITE Transactions 202
- Doorbell Transactions 202
- Port-Write Transactions 203
- Testbench Completion 204
- Chapter 7: Testbench 7–11 205
- 7–12 Chapter 7: Testbench 206
- A. Initialization Sequence 207
- MegaCore Function v12.1 209
- Additional Information 213
- Info–2 Additional Information 214
- Document Revision History 214
- Additional Information Info–3 215
- Info–4 Additional Information 216
- Note to Table: 217
- Info–6 Additional Information 218
- Typographic Conventions 218
Produits connexes et manuels pour Instruments de mesure Altera RapidIO II MegaCore Function
Instruments de mesure Altera SerialLite III Streaming MegaCore Function Manuel d'utilisateur
(68 pages)
(68 pages)
Instruments de mesure Altera Signal Integrity Development Kit, Stratix V GX Edi Manuel d'utilisateur
(52 pages)
(52 pages)
Panasonic TXD32LF72F manuali
Manuali dei proprietari e guide per l'utente per TV a cristalli liquidi Panasonic TXD32LF72F.
We fornisce 2 manuali pdf Panasonic TXD32LF72F per scaricare gratuitamente in base al tipo di documento: Istruzioni per gli Interventi
Commentaires sur ces manuels