Altera Video and Image Processing Suite Manuel d'utilisateur Page 79
- Page / 310
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Parameter Value Description
Sync signals
• Embedded in video
• On separate wires
Specify whether to embed the synchroniza‐
tion signal in the video stream or provide on
a separate wire.
Allow color planes in sequence
input
On or Off Turn on if you want to allow run-time
switching between sequential and parallel
color plane transmission formats. The format
is controlled by the vid_hd_sdn signal.
Extract field signal On or Off Turn on to internally generate the field signal
from the position of the V sync rising edge.
Use vid_std bus On or Off Turn on if you want to use the video
standard, vid_std.
Width of vid_std bus 1–16, Default = 1 Specify the width of the vid_std bus, in bits.
Extract ancillary packets On or Off Turn on to extract the ancillary packets in
embedded sync mode.
Depth of the ancillary memory 0–4096, Default = 0 Specify the depth of the ancillary packet
RAM, in words.
Extract the total resolution On or Off Turn on to extract total resolution from the
video stream.
Enable HDMI duplicate pixel
removal
• No duplicate pixel
removal
• Remove duplicate
pixel
Specify whether to enable a block to remove
duplicate pixels for low rate resolutions.
Note: The remove duplicate pixel feature
is not supported for 14.1. Set this
parameter to No duplicate pixel
removal.
Interlaced or progressive
• Progressive
• Interlaced
Specify the format to be used when no format
is automatically detected.
Width 32–65,536, Default =
1920
Specify the image width to be used when no
format is automatically detected.
Height – frame/field 0 32–65,536, Default =
1080
Specify the image height to be used when no
format is automatically detected.
Height – field 1 32–65,536, Default =
480
Specify the image height for interlaced field 1
to be used when no format is automatically
detected.
Pixel FIFO size 32–(memory limit),
Default = 2048
Specify the required FIFO depth in pixels,
(limited by the available on-chip memory).
Video in and out use the same
clock
On or Off Turn on if you want to use the same signal for
the input and output video image stream
clocks.
4-20
Clocked Video Interface Parameter Settings
UG-VIPSUITE
2015.05.04
Altera Corporation
Clocked Video Interface IP Cores
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Feature Support 7
- Release Information 9
- Device Family Support 10
- IP Core Mode Latency 11
- Interfaces 28
- Video Formats 29
- D0 D1vid_data 32
- Signal Name Description 33
- Avalon-ST Video Protocol 34
- Video Data Packets 38
- Symbol transmitted first 39
- Symbol transmitted last 39
- Plane for even rows 40
- Plane for odd rows 40
- Control Data Packets 42
- Parameters 43
- Description 43
- Type Width Height Interlacin 43
- Order Symbol Order Symbol 45
- Ancillary Data Packets 46
- Packet Propagation 46
- Parameter Name Value 47
- Signal Width Direction 47
- Packet Transfer Examples 48
- Parameter Value 50
- Avalon-MM Slave Interfaces 52
- Avalon-MM Master Interfaces 55
- Related Information 56
- Getting Started 57
- OpenCore Plus IP Evaluation 59
- Control Port 60
- Format Description 61
- Interrupts 64
- Generator Lock 68
- Underflow and Overflow 70
- Timing Constraints 71
- Handling Ancillary Packets 71
- Modules Description 75
- Address Register Description 100
- UG-VIPSUITE 105
- 2015.05.04 105
- 2D FIR Filter IP Core 106
- Coefficient Precision 107
- Parameter Value Description 108
- 2D FIR Filter Signals 109
- Signal Direction Description 110
- Video Mixing IP Cores 112
- Alpha Blending 113
- Video Mixing Signals 116
- 20 Input 3 enable 121
- Chroma Resampler IP Core 122
- 4:4:4 to 4:2:2 123
- 4:2:2 to 4:4:4 123
- Vertical Resampling (4:2:0) 124
- Chroma Resampler Signals 126
- Video Clipping IP Cores 127
- Video Clipping Signals 130
- Color Plane Sequencer IP Core 135
- Rearranging Color Patterns 136
- Splitting and Duplicating 137
- Subsampled Data 138
- Color Plane Sequencer Signals 139
- IP Cores Feature 141
- Input and Output Data Types 142
- Color Space Conversion 142
- Operands 145
- Control Synchronizer IP Core 153
- Control Synchronizer Signals 157
- Deinterlacing IP Cores 160
- Deinterlacing Methods 161
- Bob with Scanline Duplication 162
- Motion-Adaptive 162
- Sobel-Based HQ Mode 164
- Frame Buffering 165
- Types Description 166
- Frame Rate Conversion 167
- Altera Corporation 168
- Send Feedback 168
- Deinterlacing Signals 176
- Register Address 190
- (Decimal) 190
- Register Suggested 190
- Settings 190
- Comments 190
- Tuning Motion Shift 191
- Frame Reader IP Core 192
- Frame Reader Signals 194
- Frame Buffer IP Cores 198
- Double Buffering 199
- Triple Buffering 199
- Locked Frame Rate Conversion 200
- Color Format 201
- Frame Buffer Signals 206
- Gamma Corrector IP Core 214
- Gamma Corrector Signals 215
- Interlacer IP Core 218
- Interlacer Parameter Settings 219
- Interlacer Signals 219
- Interlacer Control Registers 221
- Scaler II IP Core 222
- Bilinear Algorithm 223
- Double-Buffering 226
- Scaler II Parameter Settings 230
- Scaler II Signals 233
- Scaler II Control Registers 235
- Video Switching IP Cores 237
- Mixer Layer Switching 238
- Video Switching Signals 239
- Test Pattern 243
- Trace System IP Core 253
- Trace System Signals 255
- Trace Within System Console 258
- TCL Shell Commands 259
- Command Arguments Function 260
- Packet Visualization 263
- Monitor Settings 264
- Subscribe 269
- Avalon-ST Video Class Library 270
- Class Description 272
- Running the Tests 275
- Video File Reader Test 278
- Example Test Environment 281
- Video Field Life Cycle 282
- Constrained Random Test 283
- Code for Scoreboards 285
- Code for to_grey Function 286
- Complete Class Reference 287
- Method Call Description 288
- Member Description 288
- Raw Video Data Format 299
- Y 410 / A 2R 10 G 10 B 10 301
- Additional Information 306
- Date Version Changes 307
- How to Contact Altera 310
Produits connexes et manuels pour Instruments de mesure Altera Video and Image Processing Suite
Instruments de mesure Altera Transceiver Signal Integrity Development Kit, Stra Manuel d'utilisateur
(42 pages)
(42 pages)
Instruments de mesure Altera Transceiver Signal Integrity Development Kit, Stra Manuel d'utilisateur
(58 pages)
(58 pages)
Instruments de mesure Altera Cyclone II EP2C35 PCI Development Board Manuel d'utilisateur
(50 pages)
(50 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels