Altera 10-Gbps Ethernet MAC MegaCore Function Manuel d'utilisateur Page 68
- Page / 175
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
February 2014 Altera Corporation 10-Gbps Ethernet MAC MegaCore Function User Guide
7. Functional Description
The 10GbE MAC IP core handles the flow of data between a client and Ethernet
network through a 10-Gbps Ethernet PHY. On the transmit path, the MAC accepts
client frames and constructs Ethernet frames by inserting various control fields, such
as checksums before forwarding them to the PHY. Similarly, on the receive path, the
MAC accepts Ethernet frames via a PHY, performs checks, and removes the relevant
fields before forwarding the frames to the client. You can configure the MAC to collect
statistics on both transmit and receive paths. You can opt to use either 10GbE MAC,
1G/10GbE MAC, or 10M-10GbE MAC variant.
This chapter describes the MAC IP core, its architecture, interfaces, data paths,
registers, and interface signals.
7.1. Architecture
The 10GbE MAC IP core is a composition of three blocks: MAC receiver (MAC RX),
MAC transmitter (MAC TX), and Avalon-MM bridge. The MAC RX and MAC TX
handle data flow between the client and Ethernet network.
The Avalon-MM bridge provides a single interface to all Avalon-MM interfaces within
the MAC, which allows a host to access 32-bit configuration and status registers, and
statistics counters.
- User Guide 1
- Contents 3
- Contents iv 4
- Chapter 8. Registers 5
- Chapter 9. Interface Signals 5
- 1. About This IP Core 7
- 1.2. Release Information 8
- 1.3. Device Family Support 9
- 1.4. IP Core Verification 10
- ■ Timestamping is enabled 12
- ■ ptp_1step is disabled 12
- 2.2. Design Flows 14
- 2.3.2. Simulate the IP Core 15
- 2.4.1. Specify Parameters 16
- 2.4.3. Simulate the System 17
- [1] register bit to 1 18
- 3. 10GbE MAC Design Examples 19
- 3.2.0.2. Base Addresses 22
- Table 3–5 on page 3–10 23
- Creating a New 10GbE Design 24
- 3.6. 10GbE Testbenches 26
- 3.6.3. 10GbE Testbench Files 27
- 10GbE Testbenches 28
- Notes to Table 3–6: 36
- 4.1. Software Requirements 39
- Altera FPGA 40
- Design Example 40
- 4.2.1. Base Addresses 41
- Figure 4–3. Testbench 43
- The <ip 44
- Simulator 45
- 5.2.2. Base Addresses 49
- 1G/10GbE Design Example Files 50
- 5.5. 1G/10GbE Testbench 51
- Testbench 52
- 1G/10GbE Testbench 53
- 5.5.4.2. Backplane-KR Mode 55
- 6.2.1. Base Addresses 62
- ModelSim Simulator 66
- 7. Functional Description 68
- Architecture 69
- 7.2. Interfaces 70
- 7.2.2. SDR XGMII 71
- 7.2.3. GMII 71
- 7.2.4. MII 71
- 7.3. Frame Types 72
- 7.4. Transmit Datapath 72
- 7.4.2. Address Insertion 73
- Note to Figure 7–5: 74
- 7.4.4. XGMII Encapsulation 75
- 7.4.6. SDR XGMII Transmission 76
- Figure 7–7. Endian Conversion 77
- 7.5. Receive Datapath 78
- 7.5.4. Address Checking 79
- 7.5.5. Frame Type Checking 79
- 7.5.6. Length Checking 80
- 7.5.7. CRC-32 and Pad Removal 81
- 7.5.8. Overflow Handling 82
- Congestion and Flow Control 83
- 7.7.2.1. PFC Frame Reception 86
- Figure 7–11. Fault Signaling 87
- 7.9. IEEE 1588v2 88
- IEEE 1588v2 89
- 7.9.1. Architecture 90
- 7.9.2. Transmit Datapath 91
- 7.9.3. Receive Datapath 92
- 7.9.4. Frame Format 92
- MAC Header 93
- Note to Figure 7–16: 94
- 8. Registers 95
- 8.1. MAC Registers 96
- 0x0C1. Bits 4 to 31 are 98
- 0x0C3. Bits 4 to 31 are 98
- Register Name Access 100
- Bits 4 to 31 are reserved 101
- register 111
- Name R/W Description 112
- 8.3. Register Initialization 113
- 8–20 Chapter 8: Registers 114
- Register Initialization 114
- Chapter 8: Registers 8–21 115
- 8–22 Chapter 8: Registers 116
- Chapter 8: Registers 8–23 117
- 8–24 Chapter 8: Registers 118
- Chapter 8: Registers 8–25 119
- 9. Interface Signals 120
- Note to Table 9–1: 121
- Note to Figure 9–2: 123
- Note to Figure 9–3: 123
- Notes to Figure 9–4: 124
- Note to Figure 9–5: 125
- 9.0.3. SDR XGMII 127
- Note to Figure 9–7: 128
- Note to Figure 9–8: 129
- 9.0.4. GMII Signals 130
- 9.0.5. MII Signals 130
- Note to Table 9–8: 136
- Note to Table 9–9: 139
- 1588v2 feature 142
- 10. Design Considerations 150
- 10GbE MAC XAUI/10G BASE-R PHY 151
- Reconfiguration Controller 151
- A. Frame Format 153
- Figure A–2. VLAN Frame Format 154
- A.3. Pause Frame 155
- Figure A–5. PFC Frame Format 156
- B. Time-of-Day (ToD) Clock 157
- B.4. Parameter Setting 158
- ■ Bits 20 to 31: Not used 160
- B.6.1. Adjusting ToD’s Drift 161
- C. Packet Classifier 162
- Classifier 163
- D. ToD Synchronizer 166
- D.2. Block Diagram 167
- D.4. ToD Synchronizer Signals 169
- Additional Information 171
- Info–2 Additional Information 172
- Document Revision History 172
- Additional Information Info–3 173
- How to Contact Altera 174
- Typographic Conventions 174
- Additional Information Info–5 175
Produits connexes et manuels pour Instruments de mesure Altera 10-Gbps Ethernet MAC MegaCore Function
Instruments de mesure Altera Triple Speed Ethernet MegaCore Function Manuel d'utilisateur
(223 pages)
(223 pages)
Instruments de mesure Altera 8B10B Encoder/Decoder MegaCore Function Manuel d'utilisateur
(32 pages)
(32 pages)
Instruments de mesure Altera I/O Phase-Locked Loop (Altera IOPLL) IP Core Manuel d'utilisateur
(11 pages)
(11 pages)
Instruments de mesure Altera Embedded Systems Development Kit, Cyclone III Edit Manuel d'utilisateur
(82 pages)
(82 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels