Altera Arria 10 Avalon-MM Manuel d'utilisateur Page 23
- Page / 212
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Related Information
Simulating Altera Designs
Understanding Simulation Log File Generation
Starting with the Quartus II 14.0 software release, simulation automatically creates a log file, altpcie_
monitor_<dev>_dlhip_tlp_file_log.log in your simulation directory.
Table 2-2: Sample Simulation Log File Entries
Time TLP Type Payload
(Bytes)
TLP Header
17989 RX CfgRd0 0004 04000001_0000000F_01080008
17989 RX MRd 0000 00000000_00000000_01080000
18021 RX CfgRd0 0004 04000001_0000010F_0108002C
18053 RX CfgRd0 0004 04000001_0000030F_0108003C
18085 RX MRd 0000 00000000_00000000_0108000C
Running a Gate-Level Simulation
The PCI Express testbenches run simulations at the register transfer level (RTL). However, it is possible to
create you own gate-level simulations. Contact your Altera Sales Representative for instructions and an
example that illustrate how to create a gate-level simulation from the RTL testbench.
Simulating the Single DWord Design
You can use the same testbench to simulate the Completer-Only Single Dword IP core by changing the
settings in the driver file.
1. In a terminal window, change to the <variant>_tb/<variant>_tb/altera_pcie_a10_tbed_140/sim/ directory.
2. Open altpcietb_bfm_driver_avmm.v in your text editor.
3. To enable target memory tests and specify the completer-only single dword variant, specify the
following parameters:
a. parameter RUN_TGT_MEM_TST = 1;
b. parameter RUN_DMA_MEM_TST = 0;
c. parameter AVALON_MM_LITE = 1;
4. Change to the <variant>_tb/<variant>_tb/sim/mentor directory.
5. Start the ModelSim simulator.
6. To run the simulation, type the following commands in a terminal window:
UG-01145_avmm
2015.05.14
Understanding Simulation Log File Generation
2-5
Getting Started with the Avalon‑MM Arria 10 Hard IP for PCI Express
Altera Corporation
Send Feedback
- Solutions 1
- Contents 2
- Datasheet 7
- Features 8
- Interface 9
- UG-01145_avmm 10
- 2015.05.14 10
- Release Information 12
- Device Family Support 13
- Configurations 13
- Altera FPGA 14
- Debug Features 16
- IP Core Verification 16
- Recommended Speed Grades 17
- Hard IP for PCI Express 19
- Running Qsys 20
- Generating the Example Design 21
- Time TLP Type Payload 23
- TLP Header 23
- Creating a Quartus II Project 24
- Compiling the Design 25
- Programming a Device 25
- Parameter Settings 27
- Parameter Value Description 28
- Interface System Settings 30
- Device Capabilities 34
- Error Reporting 35
- Link Capabilities 36
- MSI and MSI-X Capabilities 37
- Slot Capabilities 38
- Power Management 39
- Application Layer 48
- RX Avalon-MM Master Signals 50
- Clock Signals 55
- Signal Direction Description 56
- Serial Data Signals 60
- PIPE Interface Signals 61
- Test Signals 66
- Registers 67
- Altera-Defined VSEC Registers 75
- CvP Registers 76
- Address Range Register 80
- Bit Name Access Description 81
- Bits Name Access Description 82
- PCI Express Mailbox Registers 83
- Avalon-MM Mailbox Registers 87
- Address Name Access 88
- Description 88
- Byte Offset 88
- Register Dir Description 88
- Sending a Write TLP 93
- Bits Name Access 94
- Root Port TLP Data Registers 95
- Bits Register Description 98
- Related Information 100
- Arria 10 Reset and Clocks 101
- Clock Domains 104
- Clock Summary 106
- Interrupts for Endpoints 107
- MSI/MSI-X Support 109
- MsiIntfc_o[81:0] 110
- MsiControl_o[15:0] 110
- MsixIntfc_o[15:0] 110
- IntxReq_i 110
- IntxAck_o 110
- Error Handling 111
- Physical Layer Errors 112
- Data Link Layer Errors 112
- Transaction Layer Errors 113
- Error Type Description 114
- Status Bit Conditions 117
- Altera Corporation 118
- Send Feedback 118
- IP Core Architecture 119
- Hard IP for PCI Express 120
- Top-Level Interfaces 121
- Avalon-MM Interface 121
- Clocks and Reset 121
- Interrupts 121
- Data Link Layer 122
- Physical Layer 124
- TX Packets 125
- Avalon‑MM Bridge TLPs 129
- Byte Enable Value Description 130
- PCI Express Avalon-MM Bridge 132
- RX Block 138
- Avalon-MM RX Master Block 138
- TX Block 139
- Interrupt Handler Block 139
- Design Implementation 141
- SDC Timing Constraints 142
- Throughput Optimization 143
- Throughput of Posted Writes 145
- Optional Features 147
- ECRC on the RX Path 148
- ECRC on the TX Path 149
- TLP on Applica‐ 150
- TLP on Link Comments 150
- Subscribe 151
- Endpoint Design Example 154
- Root Complex 155
- User Application DMA 155
- Arria 10 Hard IP 155
- BAR/Address Map 156
- Avalon-MM Test Driver Module 157
- DMA Write Cycles 158
- DMA Read Cycles 160
- Offset in DMA Control 162
- Registers (BAR2) 162
- Value Description 162
- Root Port 163
- Variation 163
- (variation_name.v) 163
- Root Port BFM 164
- BFM Configuration Procedures 165
- BFM Request Interface 165
- BFM Memory Map 166
- Offset (Bytes) Description 168
- BFM Procedures and Functions 172
- Location altpcietb_bfm_rdwr.v 173
- Shared Memory Constants 181
- Constant Description 182
- Location 187
- Setting Up Simulation 199
- Debugging 201
- BIOS Enumeration Issues 203
- Frequently Asked Questions 204
- 7 6 5 4 3 2 1 0 205
- Core Config 8 4 1 205
- Additional Information 207
- Date Version Changes Made 208
- How to Contact Altera 210
- Typographic Conventions 211
- Visual Cue Meaning 212
Produits connexes et manuels pour Instruments de mesure Altera Arria 10 Avalon-MM
(207 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels